top of page

T. Parker 12g Shotgun

David Peart
2 days ago
3 min read

I have to be honest, this one broke my heart a bit. Y'all know how much I like old guns and making them work again. I could not save this one.



This old T. Parker break action 12 gauge dual-trigger side-by-side shotgun belongs to a friend. It has been in a safe for who knows how long. He asked if I could restore it and make it safe to fire. I had some doubts with my initial inspection, as the action was obviously very loose, but I accepted the challenge.





I did some research on this gun to determine its age. As far as I can tell it was made in the 1880's, I cannot find too many definitive manufacturing marks. There is no serial number that I could find on the receiver or barrels.




Locking lug
Locking lug

As stated, the gun does not lock up well at all. I did some quick cleaning to see what I had - it had lots of old grease and gunk all over the barrel lugs and locking block. The lugs had apparently been repaired at

least once, there is evidence of prior brazing of additional material on the lug locking surface. The locking block is just worn out, it will need to be replaced. Luckily it is a simple design, essentially a rectangular bar, so I could build one from scratch.









The right lock feels crisp and functional.

Worn hammer interface
Worn hammer interface

The left lock has quite a bit of wear. The hammer rotates ~20° on its lug. Both the hammer and the lug have rounding, so both will have to be welded and refit.











Firing Pin holes in standing breech
Firing Pin holes in standing breech

There is some erosion around both firing pin holes in the standing breech. The pins themselves look good, but the left pin hole has 0.017 clearance, the right has 0.024 clearance. Both are excessive and might result in blown primers and blowout through the firing pins, which could result in injury to the shooter as hot high pressure gasses, and maybe pieces of metal, get blown back into his face. The standing breech is heavy enough that it can be bushed and new firing pin holes drilled, which would be my recommended fix.


I cleaned both barrels inside and out. What I originally thought was just dirt in and just forward of the chambers is actually pitting from corrosion. I found a few dings in the barrels that are not too deep and can probably be pressed out. The pitting is bad enough that the barrels will need to be sleeved or replaced.



Barrel Proof Marks
Barrel Proof Marks

I did some research on the barrel proof marks. This gun was made in Belgium, as expected I found Liege proof marks, two in fact. One is the LEG in an oval and crown used since 1893, indicative of barrels that have been tested with black powder. The other is the script EL which is the provisional black powder proof for breech loading guns used since 1852. What I did not find is any PV proof mark, which would indicate the barrels are proofed for smokeless black powder or nitro. The PV proof marks started showing up around 1891. Since these barrels do not have the PV mark they cannot be used with modern rounds made with smokeless powder.



Firing Pins Removed and Bagged
Firing Pins Removed and Bagged

So, for all these reasons (loose lockup, excessive firing pin erosion, barrel and chamber pitting, barrel dings, and lack of modern smokeless powder proof marks) I made the hard choice to condemn this gun to being a wall hanger. I could build and fit a new locking block, sleeve the barrels, bush the firing pins, and weld and fit the loose hammer, but what's the point as this gun should not be fired. As such, I removed the firing pins and performed corrosion mitigation and general cleanup so it will look kinda pretty hanging on a wall. This gun is inoperative as it leaves my shop, and the paperwork clearly indicates it is not to be fired under any circumstance. If the customer chooses, I will weld up the firing pin holes and weld the action shut to render it permanently disabled.



I am disappointed that this gun could not be saved and made operable. It is a true classic and part of firearm history. At least it still exists as an example of 19th century ingenuity, engineering, and manufacturing. Perhaps it could have been saved if a smith had gotten to it 50 or 75 years ago.



 
 
 

Comments


bottom of page