top of page

Springfield M1903

David Peart
2 days ago
4 min read

U.S. Rifle, Caliber .30, M1903
U.S. Rifle, Caliber .30, M1903

I have been lusting after a Springfield M1903 for many years, perhaps decades. I love old guns, they just feel different than modern firearms, and I am continually amazed by the ingenuity, engineering, manufacturing, and machining that our fore fathers were able to achieve back in the 18th and 19th centuries. Keeping those old guns operating reliably, and safely, is turning into a passion for me. So I was very excited to get a chance to work on this exceptional example of a M1903!


This particular rifle was built in 1918, according to the serial number records published by Springfield Armory. From its condition, I would guess that it never saw service in WWI or WWII, or any other service. I measured the headspace at less than 0.004 inches, the firing pin has very little wear, as does the bolt lugs and cocking piece. This is a great example of these rifles that has been well cared for. Wikipedia has a good write up on the M1903 and its history if you want to learn more.



Epoxy layer on stock
Epoxy layer on stock



The customer brought this to me to help get it zeroed and to give it a general cleaning and inspection. At some point in its life someone applied epoxy to the butt stock for some reason. The customer had removed some, and asked me to remove the rest.







The first thing I did was a quick safety inspection by checking the operation of the rifle's manual safeties, the amount of lug engagement and loose breech, headspace, and firing pin protrusion. I detected absolutely no loose breech, headspace measured at less than 0.004 inches, firing pin protrusion is 0.061 in with hole clearance at 0.002. This rifle is in remarkably good shape.




Target Peep Sight
Target Peep Sight

The rear battle sight had been replaced with a target peep sight. The installation of the target sight looked good, it is tight and centered. I did a laser boresight first, and got the sight closely aligned with the bore at 100 yards. The next day I bought a fresh box of Remington 180 grain 30-06 soft point ammo and took it to Arlington Sportsman's Club to zero.






I had intended to use the 100 yard range to zero, but on this particular day the 100 yard range was full of hunters getting ready for deer season opening. Since I was expecting to go downrange often during this process to mark shots I elected to use the empty 50 yard range instead. My goal was to get the shots 'on the paper' and consistent, the customer should be able to make a slight adjustment in the sight once he gets it to a 100 yard, or more distant, range for his zeroing.



Target after Zeroing, with Twelve Shots
Target after Zeroing, with Twelve Shots

Recovered casings showing good consistent primer strikes
Recovered casings showing good consistent primer strikes





I got a decent three shot group in the upper right of the target initially. This type of target peep sight does not have graduated adjustments that click, it just slides in a dovetail. As such, I would loosen the lock screws, tap on the sight gently to move it a bit, lock it down, and repeat. It took me eight shots to get a good grouping on the bullseye, letting the barrel cool for a minute or two between each shot. For the last four shots, I loaded the magazine and racked through four shots as quick as I could operate the bolt and get the sights back on target. Yeah, I had some fun with it while I had the opportunity! These last four strung to the right a bit, mostly due to my marksmanship not the rifle.












In work removing epoxy
In work removing epoxy




I got it back to my shop and started on removing the epoxy on the stock. I found that I could chip it off bit-by-bit by gently prying it up with a sharp chisel. I had to go slow in order to prevent marring the wood. In a few spots the epoxy actually gripped the wood and the top of the grain popped off with it, leaving visible marks. Once I had the epoxy removed, I lightly buffed the stock with Grade 1 steel wool and applied some boiled linseed oil. I let the oil soak in for about 5 minutes, wiped off

Final finish after multiple applications of boiled linseed oil and buffing
Final finish after multiple applications of boiled linseed oil and buffing

the excess, then repeated this steel wool and linseed application six times. Eventually I ended up with a consistent and 'aged' finish that matched the rest of

the stock with no apparent marring from the epoxy.










Disassembled bolt and cocking piece
Disassembled bolt and cocking piece



To finish this project I did a field strip and cleaned and lubed the bolt parts, receiver, magazine, and bore. I did not see a need to take apart the trigger for clean and lube.








I have to admit that I really want this rifle, I am envious of the client. I have looked at many 1903's at gun shows and have never seen one in this remarkably good condition at any price. With a little TLC this rifle should be around for at least another 100 years!



 
 
 

Comments


bottom of page